, welcome to SQ Group! |   Add to favorites   |   Contact   |   中文版   |   SPAIN   | Listed securities: 830881
Industry Profile Products Statement Contact Way
Current Location: Home > Health Industry > Hygine Protective Equipment

Particulate Respirator

Heart-shaped: SNN70369B FFP2 NR Willow leaf-Shaped :SNN70370B FFP2 NRC-shaped:SNN200647 FFP2 NR






Heart-shaped: SNN70369B FFP2 NR         
Willow leaf-Shaped :SNN70370B FFP2 NR
C-shaped:SNN200647 FFP2 NR 
 
Filtering half masks meet the requirements of Regulation (EU) 2016/425 and are CE marked accordingly. They have been tested according to EN 149:2001+A1:2009 FFP2 NR. CE Certification body:CCQS Certification Services Limited, Block 1 Blanchardstown Corporate Park, Ballycoolin Road, Blanchardstown, Dublin15, D15 AKK1, Ireland (NB 2834).

The EU Declaration of Conformity can be downloaded from the following website:   www.shengquan.com
 
USER INSTRUCTION
① Failure to follow all instructions and limitations could seriously reduce the effectiveness of this particle half mask and could lead to illness, injury or death.
② A properly selected respirator is essential, before occupational use, the wearer must be trained by the employer in the correct use of the respirator in accordance with applicable safety and health standards.
③ This particle half mask does not supply oxygen. Use only in adequately ventilated are as containing sufficient oxygen to support life.
④ Discard the respirator and replace with a new one if:
a). Excessive clogging of the particle half mask cause breathing difficulty.
b). The particle half mask become damaged.
⑤ Leave the contaminated area if dizziness, irritation or other distress occurs.
 
FITTING INSTRUCTION
① Place fingers inside the particle half mask. Bend the nose clip around fingers to form nose shape.
② Hold the particle half mask in position over the nose and mouth, pull the ear loop behand the ears.
③ Using both hands, form the nose clip around the nose and shift the ear loop to ensure a positive face seal.
④ Fit check:
a). To test the fit of the particle half mask without an exhalation vavel, cup both hands over mask and inhale sharply.
b). If air flow is felt in the nose area, re-adjust/tighten the nose clip.
c). If are flows is felt around the edges of the respirator, re-positon the particle half mask/ear loop to achieve a better fit.
⑤ Change the mask immediately if breathing becomes difficult or mask becomes damaged or distorted.
⑥ Change the mask if a proper face seal can not be achieved.
⑦ Careful observance of these instruction is an important step in safe respirator use.
 
USE LIMATION

① Do not use the respirator or enter or stay in a contaminated area under the following circumstance:
a).Atmosphere contains less than 19.5% oxygen.
b).If you smell or taste contaminant.
c).For protection against gases or vapors.
d).Contaminants or their concentrations are unknown or immediately dangerous to life or health.
e).For sandblasting, paint-spray operations and asbestos.
f ).In explosive atmospheres.
② Do not modify or misuse the mask.
③ Do not use the particle half mask with facial hair or any other conditions that may prevent a good face-seal, the requirements for leakage will be achieved.
④ Particle filtering half mask need to be inspected prior to each use to assure there are no holes in the breathing zone other than punctures around and staples and no damaged has occurred. Enlarged holes resulting from ripped or torn filter material around staple punctures are considered damage. 
⑤ This respirator helps protect against certain particulate contaminants but does not eliminate exposure to the risk or contracting disease or infection. Misuse may result in sickness or death.
⑥ This particle half mask marked “NR”, shall not be used for more than one shift. 
⑦ This particle half mask is not suitable for users has an ear that has been damaged.

 
Manufacturer: Shandong Shengquan New Materials  Co., Ltd. 
Address : Diaozhen Industrial Development Zone, Zhangqiu District, 
Jinan, Shandong, China
Service hotline: 0086-400-777-8118  Website:www.shengquan.com
E-mail:zacktang@shengquan.com
 
USA
Company: Shengquan USA Inc. 
Address:  8889 West Olympic Boulevard, Suite 1000 Beverly Hills, CA 90211 United States of America
Contact: Jonathan Lim     Service hotline:   +7(812) 401-69-00, +7(812) 647-92-00
 
GERMANY
Company: SQ Deutschland GmbH
Address: Wilhelmshöher Allee 273A 34131 Kassel / Germany
Contact: Stefan Ost     Service hotline: +49 (0)561 810418-10
 
SPAIN
Company: SQ Insertec Europe, S.L.
Address: C/ La Bureba 2, 09007 Burgos-Spain
Contact: DIANA DAI     Service hotline: (+34)947 07 61 53
 
POLAND
Company: SQ Polska Sp. z o.o.
Address: ul. Słoneczna 43, 32-050 Skawina, POLAND
Contact: Wojciech Milc     Service hotline: 0048 (12) 256-04-26  
 
RUSSIA
Company: The Scientific And Technical Center Of Industrial Technologies LLC
Address: B.Sampsonievsky Pr.,D.45, Lit. A, 194044,St.  Petersburg,Russia
Contact:  Mikhail Lavrentyev      Service hotline: +7(812) 401-69-00, +7(812) 647-92-00 
 
BRAZIL
Company: SQ do Brasil Comercialização de Produtos Quimicos Ltd.
Address: Rua Fiação da Saúde, 145 Conjunto 48, São Paulo-SP, Brasil
Contact: Daniel Vidal     Service hotline: +55-11-974604748
 
INDIA
Company: SQ Enterprises Private Limited
Address:  No. 6/60-2,  Sylvan Gardens,G.N.Mills Post, Coimbatore-641 029,India
Contact: Regith Gopinath     Service hotline: +91-9789185555
 
AUSTRALIA
Company: Shengquan (Australia) High-Tech Pty Ltd
Address: U109,7 Hoyle Ave,Castle Hill,NSW 2154
contact: Elaine      Service hotline:+61 (02)7807 4893  \ +61 481265768
email:info@shengquangroup.com.au
 

Tags:




Add: Shengquan Industrial Park, Zhangqiu, Shandong, China   Tel: (86)531-83511609   Fax: (86)531-83511356   ICP: 05018131-9
E-mail: sqwmb@shengquan.com   Copyright 2001-2028 SQ Group All Rights Reserved.